Guide to Buy Turbid Flow Meter in Sincerity

orifice meter daily check items are as follows: first, the orifice valve surface should be clean, no paint falls off, corrosion, the nameplate is clear, complete parts in good condition, no internal and external infiltrated phenomenon, flexible to use movable parts.

Second, a monthly check for orifice valve operation, removal of orifice plate surface dirt, visual important parts of the orifice plate, if there are defects such as scratch, wear, corrosion pit, should be replaced, seal deformation must be replaced if there is any damage.
Check the content mainly include: 2,
1)

Appearance inspection: there should be no dirt, dust, corrosion of the orifice plate deformation and obvious damage.
2,
2)

Measurement aperture: refers to the new orifice plate before using the aperture of measurement, method is to use 0.

02 level roughly equal Angle on the vernier caliper, round of four azimuth measurement, the result of arithmetic mean as the measured aperture value, this value should be consistent with marked the numerical aperture of orifice plate.
2,
3)

Deformation inspection: use vernier caliper respectively abutting edge surface of the orifice, downstream face in vertical roughly two location, estimate the maximum crack width, the value and the measuring tube diameter ratio should be less than 0.
5%.
2,
4)

Sharp degree of inspection: the inspection hole orifice plate on the edge of the rectangular entrance sharp degree, if find any visible defects such as scratches, erosion and abrasion, recommend replacing orifice.
2,
5)

Pressure pipe cleaning: emptying of the monthly to the pressure pipe, purging, prevent pressure tube accumulate dirt.
2,
6)

Three valve group check: check whether there is any leakage on five valve group of high and low pressure valve cavity, the valve closed root check zero has shift after balancing valve is opened.

Intelligent electromagnetic flowmeter in the process of using, may appear all sorts of problems, different fault phenomenon and the cause of the problem is different, the following we will introduce the intelligent electromagnetic flowmeter for everyone common questions.

Intelligent electromagnetic flowmeter common problems: 1, the electrode corrosion failure reason: due to the improper choice of electrode material and electrode was measured by liquid corrosion, resulting in flowmeter output shaking.

2, the bubbles in the liquid in the liquid suction from the outside world and the formation of the gas bubble of gases dissolved in the liquid into two ways YouLiZhuang bubbles.

If the larger bubbles in the liquid, because grazed electrode can cover the entire electrode, make traffic signal input circuit transient open circuit, lead to shake the output signal.

3, lining deformation lining deformation, electromagnetic flowmeter occurs mostly in fluorine plastic lining, the causes of this phenomenon has two kinds: one is caused by steam osmosis fluorine plastic lined thermal diffusion phenomenon, the so-called thermal diffusion medium through the fluorine plastic lining when the pipe is what happens when the nature of physical phenomena, is usually the degree of infiltration mainly depend on the type of lining material, liquid and steam, the thickness of the lining, temperature difference between inside and outside the lining and pipe pressure, and other factors.

4, there is no traffic signal output intelligent electromagnetic flowmeter flow signal output, could be a power failure;
Connecting cable system fault;
Liquid flow status of the fault;

Sensor components damaged or measuring wall adhesion layer cause the failure of;
Converter fault components damage.
This is an internationally recognized standard which acts as a form of guarantee that everything Beijing Sincerity Automatic Equipment Co., Ltd does is managed to the highest quality standards.
Helping the needy insertion ultrasonic flow meter industries with quality products had been our main goal and we have succeeded in providing simple and effective solutions which has a huge scope to be implemented in the near future. Go to Sincerity Flow Meter to know more about us.
A primary strategy is superior customer satisfaction. Beijing Sincerity Automatic Equipment Co., Ltd constantly analyzes market needs around the world to develop a full range of products for different use.

Abstract: steam flow meter scale correct installation and use of the information produced by excellent flow meter, flow meter manufacturer to offer you the quotation.

Measurement of steam flow, usually choose orifice, V cone, balance sheet, pitot tube (
Ba)

The differentiae pressure meter, or vortex street, target type speed meter, etc.

A, orifice differential pressure type flowmeter, pitot tube straight section of general installation recommended in the first 10 d after 5 d, V cone.

More flow meter manufacturers choose model price quote you are welcome to inquire, below is the steam flow meter scale details correct installation and use of the article.

Measurement of steam flow, usually choose orifice, V cone, balance sheet, pitot tube (
Ba)

The differentiae pressure meter, or vortex street, target type speed meter, etc.

One, orifice differential pressure type flowmeter, pitot tube straight section of general installation recommended in the first 10 d after 5 d, V cone, balance straight pipe flowmeter recommended before 2 d after 1 d, flow meter in front of the valve, tee, elbow straight pipe, and so on and so forth.

When the steam differential pressure flowmeter measurement, if under the condition of the installation of the condensing tank, flow meter can be installed in a vertical upward, namely a pressure sensor ontology or mouth upward vertical pipe installation.

But in general, no condensing tank, the recommended flow meter installed in the pipeline level down 10 ~ 45 degrees of this range, the reason for this is to protect the transmitter will not be broken to pieces by high temperature.

Differential pressure meter heat preservation measures refer to ordinary pipeline protective measures is ok, no problem.

Temperature compensation, pressure transmitter installation 0 in front of the differential pressure flow meter.

5 meters, temperature transmitter installation 0 after the differential pressure flow meter.

5 meters is about position, almost it doesn't matter.

Because of a loss of pressure differential pressure type flowmeter, installed at the back of the meter to the pressure will be smaller, and the temperature transmitter are generally plug-in, such as PT100, there will be some disturbing situation, impact flowmeter measurement.
Second, the speed of flowmeter 1.

Considering the cost if measuring steam main is to use vortex street, vortex street can be installed vertically upward when installation, temperature compensation can be reference to the differential pressure type, * note was the location of the vortex street flowmeter installation can stay away from the motor or vibration equipment, pipeline vibration will make the vortex street flowmeter phrase.

Above is all there is in this article, you are welcome to inquire me manufacturer flowmeter selection, quotation, etc.
Looking for an innovative range of vortex flow meter manufacturer mass flow meter products? Beijing Sincerity Automatic Equipment Co., Ltd supplies a diverse range of consumer, commercial and specialty industrial products including mass flow meter, rosemount coriolis mass flow meter, insertion ultrasonic flow meter,etc.Click Sincerity Flow Meter to learn more!
Dazzle your next event with endress hauser ultrasonic flow meter mass flow meter and to buy best product， only trust Beijing Sincerity Automatic Equipment Co., Ltd.
Beijing Sincerity Automatic Equipment Co., Ltd expects to reach the desired profits in the first year and does not anticipate serious cash flow problems.
Among improvements to mass flow meter, nearly half of consumers considered quality and service as the most important change a business could make in its supply chain.
Beijing Sincerity Automatic Equipment Co., Ltd deems that we can drive consumer transactions using high-tech tools like artificial intelligence and cognitive data sets.

Abstract: the electromagnetic flow meter scale measurement principle of the information produced by excellent flow meter, flow meter manufacturer to offer you the quotation.

Electromagnetic flowmeter is applicable to measure the volume flow of conducting liquid and slurry in a closed pipe, such as clean water, sewage, all kinds of acid and alkali solution, slurry, pulp, paper pulp and liquid food, etc.

Electromagnetic flowmeter measurement principle is based on Faraday electromagnetic.

More flow meter manufacturers choose model price quote you are welcome to inquire, here is a scale electromagnetic flowmeter measurement principle, the article details.

Electromagnetic flowmeter is applicable to measure the volume flow of conducting liquid and slurry in a closed pipe, such as clean water, sewage, all kinds of acid and alkali solution, slurry, pulp, paper pulp and liquid food, etc.

Electromagnetic flowmeter measurement principle is based on Faraday's law of electromagnetic induction: conductive liquid for cutting lines of magnetic force in magnetic field movement, the potential is induced in the conductor, the induced potential E as E = KBVD type: K -
- - - - - -
- - - - - -
- - - - - -
- - - - - -
B - instrument constants
-
-
-
-
The magnetic induction intensity of V -
-
-
-
-
The measured average flow velocity in the piping section D -
-
-
-
-

Measuring the inner diameter of the pipe cross section flow, the electrical conductivity of liquid with speed V through the perpendicular to the flow direction of magnetic field, the flow of the liquid conductivity sensing out a voltage is proportional to the average flow velocity, the induced voltage signal by two or more direct contact with the liquid electrode detection, and through the cable to the converter by intelligent processing, then 4 - LCD display or converted into a standard signal
Ma and 0-20
5 KHZ output.

Above is all there is in this article, you are welcome to inquire me manufacturer flowmeter selection, quotation, etc.
Beijing Sincerity Automatic Equipment Co., Ltd is trying to institute social good changes this relationship because it averts a firm's resources from its core task of increasing profits.
Beijing Sincerity Automatic Equipment Co., Ltd strives to be the acknowledged global leader and preferred partner in helping our clients succeed in the world’s rapidly evolving financial markets.
Beijing Sincerity Automatic Equipment Co., Ltd has extented its range of manufacturing scale, which satisfys customers' needs.
Beijing Sincerity Automatic Equipment Co., Ltd has unique staffs who will serve you with their best ideas by affording you with high-quality service.
tuning fork liquid density meter mass flow meter will help keep your fork density meter manufacturer in a endress hauser ultrasonic flow meter state.

Abstract: Information on installation and maintenance of precession vortex gas flow meters is provided by excellent flowmeter and flowmeter manufacturers and quotation manufacturers. If the precession vortex gas flowmeter is improperly installed and maintained, it will not only affect the measurement accuracy, but also damage the instrument in severe cases: when moving the precession vortex gas flowmeter, the slings should be placed on the neck positions at both ends of the flowmeter flange. Do not insert into the measuring tube. For more flowmeter manufacturers to select models and price quotations, you are welcome to inquire. The following is the details of the installation and maintenance method of the precession vortex gas flowmeter. If the precession vortex gas flowmeter is improperly installed and maintained, it will not only affect the measurement accuracy, but also damage the instrument in severe cases: when moving the precession vortex gas flowmeter, the slings should be placed on the neck positions at both ends of the flowmeter flange. Do not put a pipe rod in the measuring tube for hoisting, so as to avoid damage to the lining, and at the same time, prevent the wiring socket of the screw-in vortex flowmeter from being damaged by collision. It must be ensured that the center of the precession vortex gas flowmeter is consistent with the center of the process pipeline, and the grounding wire must be connected, otherwise errors will be caused. The precession vortex flowmeter has no mechanical moving parts, small size, corrosion resistance and stable performance; it can directly display the working pressure, temperature, flow rate of the medium and the gas volume in the standard state; it has the advantages of wide range and small measurement error. It is widely used in production measurement of oil and gas wells and sales measurement of natural gas. In field applications over the years, we believe that this flowmeter is most suitable for relatively clean dry gas measurement, and has gradually become the first choice for small and medium gas measurement. It is necessary to ensure the accurate measurement of the precession vortex flowmeter and reduce the measurement error. The precession vortex gas flowmeter generally does not require daily maintenance, but the measured medium is easy to adhere or scale on the inner wall of the electrode and the measuring tube. The inner wall of the measuring tube and the electrode must be cleaned regularly, and the lining and the electrode should not be damaged. When the precession vortex gas flowmeter fails, please refer to the following reasons to find out, analyze the reasons, and eliminate the fault one by one. 1. Whether the pipeline is full, and whether the lining and electrodes are scaled. 2. Whether all cable connections are reliable. 3. Whether the grounding requirements are met. 4. Whether the magnetic coil is short-circuited or open-circuited, and whether it is insulated from the ground. 5. Whether the pipeline leaks, whether the upstream and downstream valves are affected, and whether the installation position is appropriate. The above is the whole content of this article. You are welcome to inquire about the flowmeter selection and quotation of our factory. 'Installation and Maintenance Method of Precession Vortex Gas Flow Meter'
Beijing Sincerity Automatic Equipment Co., Ltd is one of the most-trusted manufacturing suppliers to the domestic markets.
Best in Beijing Sincerity Automatic Equipment Co., Ltd can handle all sorts of tuning fork liquid density meter with good efficiency while providing ensured quality. Here you can find so as to solve your u shape coriolis mass flow meter issues.Go to Sincerity Flow Meter to get fixed.
Using high technology, mass flow meter showed its competitive advantages, captioned with information about the company's commitment to providing safe, reliable, profitable jobs to local artisans.
Beijing Sincerity Automatic Equipment Co., Ltd's main technology of mass flow meter leads us to understand and utilize information correctly.
Beijing Sincerity Automatic Equipment Co., Ltd expects to reach the desired profits in the first year and does not anticipate serious cash flow problems.