Abstract: del bar meter scale and other meter scale installation requirements of the information produced by excellent
flow meter, flow meter manufacturer to offer you the quotation.
Del the
flowmeter's installation requirements 1, for the sensor type I, has the detecting rod and a pipe welding as a body, when installation, must make the sensor in the direction of fluid flow.
The inner diameter of the inside diameter of process piping and sensor, or at least in the upstream straight.
More flow meter manufacturers choose model price quote you are welcome to inquire, here is the del bar meter scale and other meter scale installation requirements of article for details.
Del the flowmeter's installation requirements 1, for the sensor type I, has the detecting rod and a pipe welding as a body, when installation, must make the sensor in the direction of fluid flow.
The inner diameter of the inside diameter of process piping and sensor, or at least in the straight pipe upstream of the required length within the scope of the axis of the sensor with the pipe axis Angle as far as possible to zero.
1, for the sensor type I, have set up test lever and a pipe welding as a body, when installation, must make the sensor in the direction of fluid flow.
The inner diameter of the inside diameter of process piping and sensor, or at least in the straight pipe upstream of the required length within the scope of the axis of the sensor with the pipe axis Angle as far as possible to zero.
Other types of sensor is the detection of rod inserted into the process piping, in addition to the total pressure hole when installation should is opposite flow direction, must ensure that the sensor detection pole perpendicular to the axis of the process piping, which allows the location of the pressure deviation Angle.
Total pressure sensor hole center and the pipe axis Angle should be less than 7 & deg;
Sensors pole along the direction of the pipe diameter inserted to the bottom, the angular deviation is less than 7 & deg;
Vertical pipe sensor can be installed in any position along the pipeline circumferential 360 horizontal pipeline, high pressure pipe should be in the same plane, the figure 6 (
一)
As shown in.
When measuring the liquid shall be installed lateral tilt down;
When measuring gas steam should be upward sloping straight pipe installation 2, due to the sensor is based on velocity area method, the approximate integral theory, use more points to describe.
Distribution equation, and is established under the condition of the full development of the velocity distribution.
So, in order to get an ideal distribution, must be in before and after the sensor has A certain length of straight pipe number velocity-equalizing tube flow sensor installation location upstream side A downstream side B has no rectifier rectifier different plane on the same plane.
1, there is a 90 & deg;
Elbow and tee 6 d7d9d3d;
2, in the same plane with two 90 & deg;
8 d9d14d3d elbow;
3, in different plane has two 90 & deg;
Bend 9 d19d24d4d;
4, pipe diameter changes (
Or enlarge)
8 d8d8d3d;
5, partially open gate valves, ball valves, or other 8 d8d8d3d throttle valve.
Note: (
1)
In the table & other;
D”
For the pipe diameter.
（
2)
In the case of insufficient pipeline section, the upstream should be accounted for 70% of the total length of pipe, the downstream accounted for 30%, while still can give a steady value, but the accuracy of decline.
Clamping sensor device shall ensure that no leakage, no looseness, no displacement.
Above is all there is in this article, you are welcome to inquire me manufacturer flowmeter selection, quotation, etc.
Beijing Sincerity Automatic Equipment Co., Ltd has built its reputation on a commitment to providing quality products and services while rapidly responding to international needs for innovative products.
Serving others for customers a better life with
mass flow meter for employees respect and opportunity.
Looking for Manufacturers in China? Then Beijing Sincerity Automatic Equipment Co., Ltd is the right choice. we are a well known
fork density meter manufacturer mass flow meter Manufacturers and suppliers from China.
Our company is professional in manufacturing mass flow meter especially
digital fork density meter.
mass flow meter allows users to use in innovative ways that fit their individual needs, while at the same time providing cost-effective, reliable and user-friendly products.
