V cone flowmeter scale selection and installation conditions

Abstract: scale v cone flowmeter selection and installation condition information produced by excellent flow meter, flow meter manufacturer to offer you the quotation. V cone flowmeter installation site selection elements: even in v cone flowmeter is also can work normally under harsh conditions, but for the sake of the use of long-term security and stability, to install and to pay attention to the following: 1, the installation place of shock and vibration v cone flowmeter. More flow meter manufacturers choose model price quote you are welcome to inquire, here is a v cone flowmeter article details scale selection and installation conditions. V cone flowmeter installation site selection elements: even in v cone flowmeter is also can work normally under harsh conditions, but for the sake of the use of long-term security and stability, to install and to pay attention to the following: 1, the installation place factory design of the shock and vibration v cone flowmeter is can withstand the shock and vibration. But should also try to install where no vibration or vibration. 2, installation site ambient temperature conditions, please try to avoid install the meter in the environmental temperature change is big, if the installation location is directly thermal radiation or waste their exposure to day rain, waterproof, heat radiation and ventilation measures should be taken. 3, the installation place should try to avoid air condition V cone flowmeter in the corrosive environment, if used in the corrosion environment, should have good ventilation and avoid corrosive gas or liquid into the instrument. V cone flowmeter has the following installation types: 1, the pipe flange: refers to the flow meter has installed flange on both ends. And process piping ends with the specifications of the installation of flange ( Also known as the user of the flange) Connection, is relatively common structure form, the applicable scope, dn50mm ~ 3000毫米) 。 This form is applicable to the throttle device with differential pressure transmitter, at the beginning of fission installation commonly used to measure the use of steam flow, can also be used in the measurement of other high temperature medium. 2, flange clamp mounting type: for small mouth of flowmeter installation form, each meter jade process piping only 2 pieces of the flange. Flange to the process piping welded together, and then put flowmeter sandwiched between two flanges. The installation method and the vortex street flowmeter ( ≤ 300毫米) Install the same way. 3, small integration type: suitable diameter & le; Dn40mm, medium temperature & le; Fluid of 120 ℃. This structure is directly with the differential pressure transmitter tower flowmeter combined into a whole. No guide pressure pipe between them, apply pressure valve, three valve group. Make installation is very simple, The same as the vortex street flowmeter installation method) 。 Differential pressure transmitter adjust the zero point need to be closed when the process piping valve, can be zero. Note: this installation, cannot be used for measuring the occasions of high temperature medium, because of the high temperature medium into the differential pressure transmitter to measure the interior, damage the transducer to measure the diaphragm. 4, pipe butt welding type: refers to the tower flowmeter and process piping flange connection ( No flange flowmeter ontology) , when install the flow meter and directly to the process piping welded together. The structural cost is relatively low, Reduce the cost of 4 flanges) , belongs to the one-time installation. Commonly used in large diameter. 5, the integration of conventional fluid type: refers to the medium temperature & le; 120 ℃ fluid, suitable diameter: (~ dn3000. The manufacturer and user requirements, according to the different fluid on the meter when the factory welding for the user ( Or assembly) The 3 valves and valve. During installation the flowmeter with transducer assembly by the user. 6, the integration of steam type: refers to the measurement of steam flow, together with tower flowmeter, the transmitter between transmitter and flow meter to assemble my company & other; 3 valve steam group & throughout; Components, thus cancel the pressure tube and greatly simplifies the structure of pressure. 7, antifreeze liquid type: refers to the tower flow meter between the transmitter and installed by our company & other; Liquid dedicated isolation tank & throughout; Tank is equipped with special medium, the medium can not frozen at low temperatures. This kind of installation method in measuring liquid, particularly in the north in winter under the condition of low outdoor environment. Often transducer measuring room kind of liquid is easy to freeze, damage the transmitter. 8, square pipe flange: refers to the process piping is square tube, tube flowmeter measurement for circular pipe, both through a special & other; Party - Round & throughout; Fittings to connect. Above is all there is in this article, you are welcome to inquire me manufacturer flowmeter selection, quotation, etc.

mass flow meter has become a crucial product for marketers, especially when it comes to brand building and engaging potential customers.

Applied Materials’ mission is to be the leading supplier of mass flow meter worldwide-through innovation and enhancement of customer productivity with systems and service solutions.

So, what's a manufacturer to do? Familiarize ourselves with producing mass flow meter in various technologies.