The installation of the power and flow meter scale factors

Abstract: the power factors of the installation of flow meter scale information produced by excellent flow meter, flow meter manufacturer to offer you the quotation. A 1, the advantages of stable, powerful flowmeter signal power and low voltage pressure on both sides of the hole is located in the probe lientang, between the fluid and probe separation point, away from the eddy current range. 2, excellent long-term high precision power can ensure the long-term stability of accuracy. More flow meter manufacturers choose model price quote you are welcome to inquire, here is a power meter scale the article details the installation of the elements. A 1, the advantages of stable, powerful flowmeter signal power and low voltage pressure on both sides of the hole is located in the probe lientang, between the fluid and probe separation point, away from the eddy current range. 2, excellent long-term high precision power can ensure the long-term stability of precision, this is because: ( 1) Is not affected by wear, dirt and oil. （ 2) There is no movable parts structure. （ 3) On the design in addition to jam. In the front of the probe, high static pressure area around the probe, make the high pressure hole will not be blocked. Zui important, low pressure hole on either side of the probe lientang, fluid from the surface of inclined swept through, the protection of the low pressure hole will not be swept, and the other probe to congestion, because of their low pressure take pressure hole in impurities gathered in the low pressure range. 3, low cost of installation, 1) Only need a few inches of welding line, complete the installation is very simple and fast. （ 2) Application of special tools, can be achieved with a line installation. （ 3) All valves and all kinds of instrument interface for simple assembly, need very low assembly cost. Of less than 4 second, the power of the flowmeter, and the power of continuous work to fundamentally eliminate the possibility of the wall, but in the following cases, power still should pay attention to prevent: ( 1) When the pressure pipe leaking, probe high pressure equilibrium is destroyed, impurities in the smaller diameter particles are likely to enter the hole. （ 2) When pipeline in production, due to molecular Brownian movement, small particles of impurities may enter the hole. （ 3) System key frequently, formed in high, small particles of impurities may enter the hole, accumulate over a long period, it is possible to probe the jam. （ 4) Medium contains a large amount of tar, biological species, or containing fibrous material, may also cause the probe blockage. Three, power meter applications: the power meter can be used for underground pipeline industry media such as water, filtered water, circulating water flow rate measurement, such as sediment containing miscellaneous quality is big, medium temperature is not high, generally for the normal temperature, the pressure is not more than 1. 6 mpa, the less chance pipeline production and production process, basic does not have empty line outage. When we are in the selection, zui good solution is to use the online installation type power, the probe handy pull out clean. Of course, if the user of the dust removal effect is good, we also recommend using the online installation type with blowback device, can deal with most of the time. But, if you want to pull out for maintenance, only can only be carried out during production, unless specifically with a valve or threaded bolt head and barring the welding head. Four, and the power meter installation: installed on the horizontal line, when the medium is air and gas, power and should be installed in any position above 160 °, so can not guarantee in the gas liquid into the guide tube, the transmitter must be installed in a higher power and position as far as possible, open for drainage operation table. For liquid and steam is 160 ° in the lower part of any position, for liquid can make any bubbles into the pipe, when conditions permit can only be installed in the upper, the open table for exhaust operation ( Underground pipes basically the same, in the case of underground pipeline in the mud, suggested probes should be installed vertically, ensure probe medium flow is similar on both sides, make the hole less blocking) Allows for steam condensation water enters the guide pipe into the condensing pipeline, transmitter power must be installed as far as possible below the position. In vertical pipe runs for installation, can be installed in vertical pipe runs around the 360 ° any location ( Meet the straight pipe section) , pay attention to the correction after installed probe direction, the direction of the fluid on the probe '- >' and direction of pipeline fluid keep within 3 ° five power, the maintenance of the flowmeter due to the calculation of flow meter power differential pressure is small, generally not to drain, if long time blowdown will break the probe of high pressure hole pressure balance, will lead to the row of the wall, still can make low pressure hole jam, low flow indicator after open the table again, so normally in the instrument maintenance system checks and only one meter to zero, especially important for measuring instrument can take on a regular basis to clean power and the probe, once/month, for example, when cleaning inspection probe and the positive and negative pressure hole appearance dredge situation, at the same time in order to ensure the accurate measurement of pressure is relatively uninteresting facts in recovery when installation must ensure that the measuring system of the static sealing point don't leak. Above is all there is in this article, you are welcome to inquire me manufacturer flowmeter selection, quotation, etc.

We are a performance driven culture that uses mass flow meter to ensure continuous improvement.

Beijing Sincerity Automatic Equipment Co., Ltd take prudent risks and work together to assure our success and profitability in the future.

To properly understand what customers want, when, why and how they want it, Beijing Sincerity Automatic Equipment Co., Ltd needs to pivot toward sentiment analysis, a burgeoning technology that taps into consumer demand based on natural language processing.

Beijing Sincerity Automatic Equipment Co., Ltd’s model also predicts (i) a positive effect of management on firm performance; (ii) a positive relationship between product market competition and average management quality (part of which stems from the larger covariance between management with firm size as competition strengthens); and (iii) a rise (fall) in the level (dispersion) of management with firm age.