Installation points and application scope of remote water meters

Abstract: The installation points and application range information of remote water meters are provided by excellent flowmeter and flowmeter manufacturers and quotation manufacturers. The remote water meter is composed of an ordinary mechanical water meter and an electronic acquisition and transmission module. The electronic module completes signal acquisition, data processing, storage, and uploads the data to the repeater or hand-held meter reading device through the communication line. The watch body adopts a one-piece design, it can. For more flowmeter manufacturers to select models and price quotations, you are welcome to inquire. The following are the installation points and application details of remote water meters. The remote water meter is composed of an ordinary mechanical water meter and an electronic acquisition and transmission module. The electronic module completes signal acquisition, data processing, storage, and uploads the data to the repeater or hand-held meter reading device through the communication line. The meter body adopts an integrated design. It can record and save the user's water consumption in real time, or directly read the current accumulated number. Each water meter has a code. When the smart water meter receives the meter reading instruction, it can immediately upload the water meter data to the management. System remote water meter installation points 1) The water meter should be installed in a place that is convenient for maintenance and reading, free from exposure to sunlight, freezing, pollution and mechanical damage. 2) The front end of the screw-wing water meter should have a straight pipe of 8~10 times the nominal diameter of the water meter, and there should be a straight pipe of no less than 300mm before and after other types of water meters. 3) The rotor type water meter and the vertical screw type water meter should be installed horizontally; the horizontal screw type and volumetric water meter can be installed horizontally, inclined or vertically according to the actual situation; when installed vertically, the water flow direction must be from bottom to top. 4) For the water supply system that integrates life, production and fire protection, if there is only one inlet pipe, a bypass pipe should be installed around the water meter. 5) Maintenance valves should be installed before and after the water meter and on the bypass pipe, and drainage devices should be installed on the water meter and the valve behind the meter. In order to reduce the loss of water head and ensure the straight flow of water flow in the pipe in front of the meter, the gate valve should be used for the maintenance valve in front of the meter. For household water meters in residential buildings, the maintenance valve behind the meter and the special drainage device may not be provided. 6) Water meter wells should be protected from flooding and rainwater. 7) The direction of the water meter should be consistent with its type. 8) When the water meter may reverse, affect the measurement and damage the water meter, a check valve should be set behind the water meter. 9) The installation requirements of the hot and cold water meters are basically the same except for the different working temperatures. The maximum operating temperature of the hot water meter is 110°C. If the hot water meter is installed in front of the boiler or heat exchanger, in order to prevent backflow, a check valve should be installed behind the water meter. 10) There are two ways to install the remote water meter: the installation of the remote water meter that only plays the role of outdoor meter reading is relatively simple, as long as the water meter output system is connected to the data display device (repeater) installed outdoors; Another way is to connect all remote water meters of the whole building or the whole community to the community management department through repeaters and network controllers, and conduct unified management through terminal equipment. The above is the whole content of this article. You are welcome to inquire about the flowmeter selection and quotation of our factory. 'Installation points and application scope of remote water meters'

Everyone who has a endress hauser coriolis mass flow meter wants it to look coriolis density meter. However, in order to achieve that, it normally involves investing in a fork density meter manufacturer mass flow meter. Beijing Sincerity Automatic Equipment Co., Ltd can offer you the best solution.

Looking for a company to handle your mass flow meter electromagnetic flow meter slurry? Visit Sincerity Flow Meter today for more information.

Turn to Beijing Sincerity Automatic Equipment Co., Ltd if you are looking for premier v shape coriolis mass flow meter solution, affordable packages, and quality mass flow meter products! We produce wide series of high quality, first-class , and provide professional mass flow meter services at great prices.

Many business owners and professionals use services like Beijing Sincerity Automatic Equipment Co., Ltd to stay on top of manufacturing industry, monitor products’ quality and keep an eye on competitors.

In various different types of endress hauser ultrasonic flow meter, tuning fork liquid density meter mass flow meter is one of the most commonly used.