Installation and use strategy of plastic tube rotor flow meter

Abstract: The information on the installation and use strategies of plastic tube rotor flowmeters is provided by excellent flowmeter and flowmeter manufacturers and quotation manufacturers. The main parts of the HC-LZS plastic tube rotameter cone tube are made of AS, ABS plastic, which has good corrosion resistance, reasonable structure, small volume, light weight, and the cone tube is not easy to break. Can be widely used in chemical, environmental protection, food and other industrial sectors. . More flowmeter manufacturers select models and price quotations. You are welcome to inquire. The following is the details of the article on the installation and use strategy of plastic tube rotor flowmeters. The main parts of the HC-LZS plastic tube rotameter cone tube are made of AS, ABS plastic, which has good corrosion resistance, reasonable structure, small volume, light weight, and the cone tube is not easy to break. Can be widely used in chemical, environmental protection, food and other industrial sectors. The main measuring element of the plastic tube rotameter is a tapered plastic tube with the small end down and the big end up vertically and a float that can move up and down inside. Installation of plastic tube rotameter [1] Before installation, the foam support in the meter should be gently taken out with needle-nose pliers, and then re-installed. When installing, pay attention to whether the rubber gasket is installed in the connecting pipe. in the tank to prevent water leakage. [2] The interface of the flowmeter can be connected with the matching ABS plastic pipe, or with the PVC plastic pipe, which can be connected with special glue, or can be connected with the metal flange after connecting with the plastic method. [3] The flowmeter must be installed vertically without obvious inclination. The installation height should be convenient for the reading of the float. When reading, the line of sight and the float should be level. [General standard: the required flow rate is 50%-70% of the maximum flow rate of the flowmeter, try not to use the highest number. ][4] There should be a straight pipe section with 5 times the diameter of the instrument at the inlet and outlet of the instrument. [5] The pressure of the fluid on the side of the flowmeter must be stable. If the fluid is too unstable, the float will fluctuate and cannot be measured correctly. A buffer or a valuer should be installed upstream of the flowmeter. [6] The plastic tube rotameter should be installed vertically, and the angle between the center line of the flowmeter and the plumb line should not exceed 5 degrees. When the plastic tube rotameter is used as an instrument [1], the upstream valve should be slowly opened to fully open, and then the flow rate should be adjusted with the regulating valve downstream of the flowmeter. When the instrument is out of use, the upstream valve should be slowly closed first, and then the flow regulating valve downstream of the instrument should be closed. [2] The indication value of the meter is seen in the middle of the scale line, and the value is read from the scale of the float according to the height of the float. [3] When the cone tube and the float are dirty, they should be cleaned in time. [4] Regularly check the error of the flowmeter. Once the specified error is exceeded, the float and cone should be replaced, or re-calibrated to obtain better accuracy. [5] When the measured fluid is inconsistent with the calibration medium of the flowmeter, it is necessary to correct the indication value. It is expressed by the following formula The above is the whole content of this article. You are welcome to inquire about the flowmeter selection and quotation of our factory. 'Plastic tube rotor flow meter installation and use strategy'

Every day of the year, there is some city or town in the world that is changing over to for coriolis mass flow meter emerson.

For many years, Beijing Sincerity Automatic Equipment Co., Ltd has searched for and found a number of secrets to help you u shape coriolis mass flow meter. Go to Sincerity Flow Meter to learn about some of those secrets.

Beijing Sincerity Automatic Equipment Co., Ltd will do this by managing our business with integrity and the highest ethical standards, while acting in a socially responsible manner with particular emphasis on the well-being of our teammates and the communities we serve.

Beijing Sincerity Automatic Equipment Co., Ltd are trained to think about problems and coming up with solutions, as well as presenting the whole idea in a logical and coherent manner.