How to install the vortex flowmeter correctly

Abstract: The information on how to correctly install the vortex flowmeter is provided by the excellent flowmeter and flowmeter manufacturers. There are the following points for attention in the installation of vortex flowmeter: 1. Reasonable selection of installation location: Avoid strong power equipment, high frequency equipment, strong power switch equipment; avoid the influence of high temperature heat sources and radiation sources, avoid Strong vibration places and strong corrosion. For more flowmeter manufacturers to select models and price quotations, you are welcome to inquire. The following is the article details on how to install the vortex flowmeter correctly. There are the following points for attention in the installation of vortex flowmeter: 1. Reasonable selection of installation location: avoid strong power equipment, high frequency equipment, strong power switch equipment; avoid the influence of high temperature heat sources and radiation sources, avoid Strong vibration places and strong corrosive environments, etc., at the same time, it is necessary to consider the convenience of installation and maintenance. 2. Installation on horizontal pipelines is the most common installation method for vortex flowmeters. When measuring gas flow, if the measured gas contains a small amount of liquid, the sensor should be installed at a higher part of the pipeline. When measuring liquid flow, if the measured liquid contains a small amount of gas, the sensor should be installed at the lower part of the pipeline. The piping upstream and downstream of the installation point should be concentric with the sensor, and the coaxial deviation should not be less than 0.5DN. 3. There must be enough straight pipe sections upstream and downstream. If there are two 90s in the same plane upstream of the sensor mounting point. Elbow, then: upstream straight pipe section≥25D, downstream straight pipe section≥5D. If there are two 90s on different planes upstream of the sensor mounting point. Elbow, then: upstream straight pipe section≥40D, downstream straight pipe section≥5D. The regulating valve should be installed beyond 5D downstream of the sensor. If it must be installed upstream of the sensor, the upstream straight pipe section of the sensor should not be less than 50D, and the downstream should not be less than 5D. 4. Vibration reduction measures shall be taken for the pipeline. Try to avoid installing the sensor on the pipeline with strong vibration, especially the lateral vibration. If the installation is unavoidable, vibration reduction measures must be taken, and pipe fastening devices and anti-vibration pads should be installed at the upstream and downstream 2D ​​of the sensor. 5. The sensor is installed on the side of the horizontal pipe. No matter what kind of fluid to measure, the sensor can be installed on the horizontal pipeline, especially for superheated steam, saturated steam and low temperature liquid. 6. The installation of the sensor in the vertical pipeline. When measuring gas flow, the sensor can be installed on vertical pipes with unlimited flow direction. If the measured gas contains a small amount of liquid, the gas flow should be from bottom to top. When measuring liquid flow, the flow direction should be from bottom to top: this will not add extra liquid weight to the probe. 7. Selection of pressure measuring point and temperature measuring point. According to the needs of the measurement, when the pressure and temperature need to be measured near the sensor, the pressure measurement point should be at 3-5D downstream of the sensor, and the temperature measurement point should be at 6-8D8 downstream of the sensor. Pack. This installation method is generally not recommended. This installation method is not suitable for measuring general gas and superheated steam. It can be used to measure saturated steam, and it is suitable for measuring high temperature liquid or when the pipeline needs to be cleaned frequently. When measuring high temperature steam, the insulation layer should not exceed a maximum of one-third of the height of the bracket. Vortex flowmeter-Huawei Yuanhang Automation Instrumentation The above is the whole content of this article. You are welcome to inquire about the flowmeter selection and quotation of our factory. 'How to install the vortex flow meter correctly'

electromagnetic flow meter slurry mass flow meter is generally used to v shape coriolis mass flow meter.

We are a provider of a various number of services that include . Search our website by mass flow meter endress hauser coriolis mass flow meter product line or category to find what you are looking for.

mass flow meter, is an alternative product for fork density meter manufacturer to investors and consumers who are passionate about our products or services.

Many business owners and professionals use services like Beijing Sincerity Automatic Equipment Co., Ltd to stay on top of manufacturing industry, monitor products’ quality and keep an eye on competitors.